Framed Ornament Tutorial

I have used card stock and fun foam (craft foam sheet) to make cross stitch fridge magnets but it recently occurred to me that I could use the same method to make cross stitch ornaments too.

Click here to view, download or print a pdf version of this tutorial.

 photo front.jpg

(From Stoney Creek "Snow Happens". Stitched on 22 count hardanger)

For this ornament I use two squares of red embossed card stock and one of 2 mm thick black fun foam. (I bought some red fun foam for this but the bold black back stitching called out for the black fun foam.)

 photo elements.jpg

First I cut a 3 inch strip of the embossed card stock. (A quilt ruler and mat knife, or rotary cutter, really speeds up this project and make the pieces more uniform.)

 photo strip.jpga>

Then I cut the strip into two squares.

 photo square.jpg

I wanted to cut a 2 inch square from the center of one of the red squares. I drew a line 2 1/2 inches from each edge ...

 photo mark.jpg>

...then used a mat knife to cut out the square.

 photo cut.jpg

I checked the square against the stitched piece...

 photo check.jpg

...then trimmed the stitched piece to a 2 1/2 inch square. (Halfway between the two inch opening and the three inch frame.)

 photo cropped.jpg

Next I applied some glue stick to the back of the card stock frame ...

 photo gluestick.jpg

...flipped it over and centered the opening over the stitched piece. (I like to use glue stick for this step because it allows me to reposition the stitched piece until I am satisfied that it is well centered.) When it was well centered I pressed the card stock firmly against the fabric.

 photo placement.jpg>

Because I didn't want the black fun foam to show through the white fabric I covered the back of the stitched piece with a piece of white acid free paper. (When I have used black fun foam under black fabric I haven't used paper.) I cut the paper just a little bigger than the fabric square, applied some glue stick to the edges of the paper ...

 photo paper.jpg

...and pressed it in place over the fabric.

 photo papertwo.jpg

Then I applied double sided tape to all four edges of the frame/ paper. (I like to use double sided tape for this step because it adheres right up to the edge and, unlike glue, I don't have to worry about it oozing out the sides.) I pressed the tape firmly to the surfaces and then removed the backing paper from the tape.

 photo doublesidedtape.jpg

Next I carefully placed the frame and fabric tape side down onto one corner of my fun foam, making sure that the two edges lined up perfectly. When I was satisfied I pressed the frame to the foam with gentle pressure on all four edges.

 photo funfoam.jpg

Then I cut the foam so that it exactly conformed to the other two edges. I used scissors but someone braver than I am might use a mat knife. (To get a nice smooth straight edge with scissors open them all the way and make one long cut instead of opening and closing the them repeatedly.)

 photo cutfoam.jpg

Next I added the hanger string. (For this ornament I used a piece of black Perle cotton but metallic thread or narrow ribbon would also be good choices.) For square ornaments I don't try to get the hanger perfectly centered. I usually place the hanger about 1/3 of the way across the top of the ornament so that it will hang at a jaunty angle. I fastened the hanger to the back of the fun foam with a bit of quick drying glue, but a bit of double sided tape would have worked well tool.

 photo hanger.jpg

I applied the double sided tape to the four edges of the second piece of card stock, pressed it firmly in place and removed the backing paper.

 photo P1000604.jpg

Then I carefully laid the second square of embossed card stock on the fun foam. It is very important to take this step slowly because once the tape contacts the fun foam it is difficult to lift it without damaging the card stock. To make sure that the card stock fit properly on the fun foam I lined up one corner perfectly and then carefully lined up the opposite corner. When I was satisfied I pressed all edges of the card stock against the fun foam. (If I had any talent for design I would have stitched something like "There's no people like Snow People" and framed that for the back. Maybe I could just get it printed on some nice paper and frame that instead...)

 photo back.jpg

Corner view.

 photo corner.jpg

Finally, to improve the contact between the tape and the other surfaces, I laid the ornament face down on a piece of felt over a flat surface and placed a heavy book on top of it. After a couple of hours it was ready to wrap or display.

 photo finish.jpg

When I have all the materials and equipment assembled in advance, and I'm not taking photos, I can put one of these ornaments/ magnets together in about 20 minutes.

 photo P1000608.jpg

Variations on the theme

1) I believe that a crafty person who is well equipped with things like circle cutters or a die cut machine could take this finish in some interesting directions.

2) A very similar finish could be crafted with two pieces of mat board.

3) The hanging thread could pierce the ornament and then be threaded through a button or sequin star or snowflake or other embellishment.

4) Or ...

Click here if you'd like to view, download or print a pdf version of this tutorial.

 photo smallpinwheel-1.jpg
Pinwheel 2010


  1. I am going to have to make a "pinwheel" binder for all your wonderful tutorials!! You are amazing!! Thanks so much for sharing your knowledge with all of us!

    Linda in Colorado Springs

  2. Great tutorial. I love the finished project.


  3. Thank you both for your words of encouragement.

    Linda I've never really thought of it as "knowledge". To me it is just the stuff that I have figured out through trial and error experiments.

  4. Re the x stitch, you said it was done on 22 ct fabric. When stitching, did you go over 2 threads ???


  5. Thank you for your question. The fabric was 22 count hardanger. It is woven so that there are 22 pairs of threads for every inch. When I stitched (with a single strand of floss) I stitched over a pair of threads. In other words I stitched so that there were 22 Xs per inch.

  6. Great tute! I just made two ornaments for a swap and used it to finish them.

  7. It is very kind of you to let me know you used the tutorial Lauriejo. (Which reminds me I need to leave some feedback on tutorials I have recently used.)